Bally Em Slot Machine Parts

Posted By admin On 08/04/22

Bally Em Slot Machine Payout Parts
Slot Machine Parts Store
Bally Slot Machine Repair Parts
Bally Slot Machine Troubleshooting
Bally S5500 Slot Machine Parts
Bally Em Slot Machine Parts

SOLD - PARTSPac/Ms. Pac upright transformer assy + wrg
SOLDSOLDSOLDSOLDFree + shipping from 23322.IF I TRIM A CENTIMETER OFF OF THE WOODEN MOUNTING PLATE, it will fit in a Large Flat-Rate USPS box and be $20.Was from a pac upright. Cant tell if it was mini or full sized. Based on the length of the wiring, I'm going to guess full upright, but...
- Thread
- bally galaxian midway ms.pac pacman
- Replies: 3
- Forum: Trading: Videogame - For Sale (Parts - One Off)
Bally Sente hattrick problem
Hello, I recently acquired this Bally Sente hattrick cabinet. It appears to have had some water damage in the past. The unit boots to this screen with lines in it, sometimes it flashes and changes colors. Small graphical pixelated glitches some times flash. I’ve looked over the main pcb and...
- Thread
- bally hattrick sente
- Replies: 0
- Forum: Technical - Videogames - General Repair And Help
Bally Pool Sharks IRQ Failure
So I have a Bally Pool Sharks in shop that started throwing IRQ Failure on boot up today. I recently replaced the batteries on the MPU and checked for any corrosion damage from the old set. It was working fine in the field, but for whatever reason today it's acting up.The diagnostic LED...
- Thread
- bally irq pinball pool sharks
- Replies: 3
- Forum: Pinball Machines
Playboy Bally Pinball - San Marcos, TX (auction)
Online auction, ends in about 9 days:https://atxauctions.hibid.com/lot/55528940/playboy-bally-pinball
- Thread
- bally pinball playboy
- Replies: 0
- Forum: External Auctions and Ads
Slot Machine Parts Lot!
A large lot of slot machine parts, mostly IGT S+ & PE+, there are also some Bally 5500 parts. These are out of a unit I had gotten and are sold as-is as I have no way to test anything. Best offer gets it all! I have no problem packing everything up for shippng, buyer to pay the actual shipping...
- Thread
- bally igt slot machine
- Replies: 0
- Forum: Slot Machines
Timber Joysticks
What are you guys going to use for Timber joysticks now that the control panels and cabinets are done? I would really like to use Bally Midway type sticks with the leaf switches and have the look of the real thing. I was told that a Galaxian joystick will work but there are none for sale...
- Thread
- bally joystick leaf midway timber
- Replies: 4
- Forum: General Arcade and Videogame Discussions
SOLD - GAMEFireball EM in Indiana
SOLD1972 Bally Fireball EM for sale. This one I really don't want to sell, but need the space back. MANY new parts including flipper rebuild, new light sockets, fuse block, glass, etc... Backglass is perfect and absolutely stunning, playfield is decent (not as bad as many, but definitely not...
- Thread
- bally electromechanical fireball pinball
- Replies: 1
- Forum: Trading: Pinball - For Sale
Wanted: control motor gearbox Twin Pirate Gun
Bally Twin Pirate GunTwo of the gears (the plastic ones) are missing teeth in the 'control motor' assembly, part # 40-606. The electric motor is fine, what I need is the gearbox or the two plastic gears from the gearbox.
- Thread
- bally gun pirate shooting
- Replies: 0
- Forum: Mechanical, Electro-Mechanical, & Oddities
WTB: Bally Four Million BC project machine or playfield
WTB: Bally Four Million BC project machine or playfieldI am looking for a project Bally Four Million BC or just the playfield. Let me know what you have. Thanks
- Thread
- bally four million machine play field project
- Replies: 0
- Forum: Trading: Pinball - Wanted
New Member w/old pinball machine
Hello,This Christmas I received something I’ve wanted for years. A pinball machine. It is a 1972? Bally “El Toro” and it is in pretty good condition for its age. There isnt anything that makes it stand out, but the fact that my friends got it for me I think it’s perfect. It does have a couple...
- Thread
- bally el toro fuses
- Replies: 2
- Forum: New Member Introductions
Bally Slot Machine...Gold Rush!
- Thread
- bally slot slot machine
- Replies: 0
- Forum: Trading: All Other Machines - For Sale
FS Parts:Bally Sente Wiring Harness
For Sale: Main wiring harness for incoming power. Power cord end was cut off, but the rest is there. Hopefully someone can get some use out of it. $20 SHIPPED in the lower 48 states. Ships within 2 business days of receiving Paypal. Thanks for looking.
- Thread
- bally harness power sente wiring
- Replies: 1
- Forum: Trading: Videogame - For Sale (Parts - One Off)
FS Parts:Bally Sente Sound Board, Power Board and plate $110 SHIPPED
Bally Sente Sound Board, Power Board and plate $110 SHIPPEDFor Sale: Bally Sente power supply board and sound board, mounted to the plate. $110 shipped in the lower 48. Boards ship within 2 business of receiving Paypal. Thanks for looking.
- Thread
- bally board power sente sound
- Replies: 1
- Forum: Trading: Videogame - For Sale (Parts - One Off)
FS Parts:**SOLD** Bally Sente MPU motherboard w/ Mini Golf $140 shipped
**SOLD** Bally Sente MPU motherboard w/ Mini Golf $140 shipped**SOLD** Bally Sente MPU motherboard w/ Mini Golf $140 shipped in the lower 48 states. I accept Paypal via the gift option and ship within 2 business days or receiving payment. Thanks for looking.
- Thread
- bally mini golf motherboard mpu sente
- Replies: 0
- Forum: Trading: Videogame - For Sale (Parts - One Off)
SOLD - PARTSSIX (6) Bally/Midway 90414 power supply boards for parts/repair
SIX (6) Bally/Midway 90414 power supply boards for parts/repairNO longer available.
- Thread
- 90414 bally galaga midway
- Replies: 0
- Forum: Trading: Videogame - For Sale (Parts - One Off)
FS Parts:Bally Sente Boards, cartridges and power supply
Ive changed this to a FOR SALE ad rather than MMAO for obvious reasons. I have the MiniGolf set with harness, sound board, cartridge, motherboard on mounting plate, as well as the control panel with ball. I can sell individual parts, but the boards are $120 shipped, with cartridge is $140...
- Thread
- ballybally sente hat trick mini golf sente
- Replies: 10
- Forum: Trading: Videogame - For Sale (Parts - One Off)
Wanted: Bally Star Trek CPR Playfield
Hi everyone , I'm looking for a Bally Star Trek CPR Playfield. PM me if you have one you would sell. Thanks
- Thread
- bally cpr play field playfield star trek
- Replies: 0
- Forum: Trading: Pinball - Wanted
WTB Bally Midway Coin door large
Looking for one of these to complete a project.Anyone got one for sale?
- Thread
- bally coin door midway
- Replies: 0
- Forum: Trading: Videogame - Wanted
Bally S6000 dragon Wheel, need help
Ok, recently purchased a bally dragon wheel slot machine. Got everything setup. Did a ramclear with chips. The game is up and running. Buy have a couple of questions.1. I have 24 volts on the cabinet, if you touch anything else and ground out you get alittle shock (24 volts ain't bad lol).2...
- Thread
- bally dragon wheel s6000 slot machine
- Replies: 2
- Forum: Slot Machines
WTB: Bally/Williams Knocker ASSY B-10686-1 W/ 23-800 COIL
WTB: Bally/Williams Knocker ASSY B-10686-1 W/ 23-800 COILDoes anyone have a spare Knocker Assy B-10686-1 with the 23-800 coil and the 3 pin connector? This is for a Bally Williams WPC era pin. Picture is for reference of what I am looking for.Thanks in advance.
- Thread
- bally knocker
- Replies: 1
- Forum: Trading: Pinball - Wanted

Repair Tips for Reel Readers

How to test and what to look for when doing your own repairs

When one of these goes bad you may see an error that would be 4x or 7x where x indicates thereel position, i.e. a 43 error code would indicate the reel reader on the third reel.

Bally Bill Validators. Call Us: Worldwide Gaming 2195 Daniels Street Suite 101 Long Lake, MN 866-679-4761 toll free 763-253-0230 main 763-253-0232 fax info@worldwide-gaming.com. You may be able to solve your equipment's problem with the right parts. Along with Bally slot machine parts, we carry a variety of other brands. Note: We have thousands of parts and take the time to clean, calibrate, and test in an actual machine. Before shipping. All pictures are for reference only and may not reflect the actual parts cleanliness. You may be able to solve your equipment's problem with the right parts. Along with Bally slot machine parts, we carry a variety of other brands. Note: We have thousands of parts and take the time to clean, calibrate, and test in an actual machine. Before shipping. All pictures are for reference only and may not reflect the actual parts cleanliness.

What is described below is for testing the reel reader card using this home built tester. The tester provides both a 50 volt source or a 5 volt source (switch selectable).

After describing this procedure I will tell you how to test the cards with out having to have a 50 volt source.

I designed and built a tester to make troubleshooting easier. I test the card and all of the photo-transistors
first, then I split the two halves of the card, one for cleaning but also so that I can use a dental tool, poking
it into the tiny opening to push the photo-transistor or IR Emitter back up and out of the small square opening. The photo-transistor/Emitter should be at something close to a 45 degree angle.

Once the bad components are pushed out of the way, I use my soldering iron to melt the solder on both leads at the same time while grasping the upper portion of the optic. It comes off very easily. Once removed use solder wick to remove the excess solder. You want to do this so that when you put in the new device the leads will be nearly flat on the PC board.

Replace the defective components and quickly tack one side, allow the solder to cool and then solder the other side. Once the other side has cooled you can go back and firmly solder the lead that was previously tacked. Reassemble and then retest to make sure that the optics are working properly. Tapping the top of the card lightly with the handle of a screw driver will show any intermittent connections.

The one question that may come up is what constitutes a bad device. Since the reader cards supply signals to TTL logic devices then we can use standard logic levels of 2.0 volts as a high and .8 volts as a low. When measuring the output of the photo transistor, if the voltage is less than 2.0 volts, while unblocked or higher than 0.8 volts when blocked then that photo-transistor (or emitter) is defective.

In the cards that I have repaired I typically see voltages of greater than 4 volts unblocked and .01 volts blocked for the 50 volt reader cards, 5 volt reader cards the unblocked voltage is 3.14 and the blocked voltage 0.2.
Test all of the emitters and photo-transistors first, the replace all defective ones. I make it a habit to clean the bulbs with alcohol on the 50 volt cards so that as much light as possible gets to the photo-transistor.

Testing reel readers without having a 50 volt source.

The 50 volt supply is only used to power the incandescent bulbs. They are in series along with the 470 ohm resistor. Each bulb requires 5 volts to operate properly.

You need a few basic items, a Volt/Ohm meter (DVM) , a 47K resistor, a light source (flashlight) and some clip leads and a 5 volt DC power supply

Split the cards by removing the 2 screws and lay the small card off to the side

If you lay the card flat on its back with the mounting bracket to the left then the pins at the bottom will number 1 through 16 from right to left
Measure the resistance between pin 16 and 14, Pin 16 is Vcc and 14 is Ground you should have a reading a bit above 500 ohms, indicating that the 470 ohm 2 W resistor and all of the bulbs are OK. If not in this range then you will have to remove the tape covering the backs of the bulbs and then measure resistance across each bulb individually. Remember the bulbs are wired in series like the old Christmas tree light strings.

Assuming that the bulbs and resistor are OK. Attach the ground lead of the volt meter and one end of the resistor to pin 14 (pairs 13/14)
of the card. Connect the other end of the resistor and the positive lead of the volt meter to pin 11.

Now using the 5 volt supply, apply 5 volts to pin 1 of the card and read the voltage, shine the light into the small (tiny) hole that is for Q1, voltage should be some where around 4.7 volts with the light on and some where less than 0.2 volts with the light off. Just keep in mind that ambient light might cause the light off reading to be higher. The acceptable voltage ranges need to be within the acceptable ranges used in ‘Logic” circuits so a logic high you need 2 volts or more and a logic low 0.8 volts or less.

You may find that if you have these readings, a Q-tip dipped into alcohol can be used to clean the top of the photo-transistor by pushing the Q-tip into the hole and then twisting the Q-tip. I routinely clean these as well as to clean the bulbs.

Repeat this process for each of the following pins 1, 3, 5, 7, 9

Other than pin 11, all of the other pins are in pairs

Pins 1 & 2 Collector of Q1
Pins 3 & 4 Collector of Q2
Pins 5 & 6 Collector of Q3
Pins 7 & 8 Collector of Q4
Pins 9 & 10 Collector of Q5

Pin 11, Common emitter
Pin 12 Missing (pin is cut off)

Bally Em Slot Machine Payout Parts

Pins 13 & 14 Ground
Pins 15 & 16 Vcc
This process is not nearly as quick or accurate as using the tester but should allow you to test each of the cards.

The 5 volt card testing process is not much different other than it is not necessary to split the cards and you need a 3K resistor instead of a 47K resistor.

Apply the 5 volts across pins 16 and 14 and then measure the voltage on the associated
pin pairs.
In this case the 3K resistor attached to pin 14 and pin 11 biases another transistor’s base (Q6), pulling it low so that it will turn on the IR Emitters. Remember to block the light for each IR emitter to see the photo-transistor transition to a low state.

Testing results for the 5 volt cards readers you will not read anywhere near 4.7 volts, they will be closer 3.0 volts for a high and about 0.2 volts for a low

Repair Tips for Power Supply

Slot Machine Parts Store

I have noticed that the schematic for the Bally E1000/E2000 power supplies list expected voltages, but, what does that mean?

I have a couple of these power supplies so I decided to do some testing to see what voltages were obtained under certain circumstances.

If you apply 12 VAC across pins 1 and 10 of the board J1 connector,you should be able to measure the voltages on the test points (+UR, ZC and 5V)

Bally Slot Machine Repair Parts

These voltage readings are based on a supply that has no load (nothing else connected)

UR = 15.96 VDC
ZC = 10.07 VDC
5v = 5.0 4VDC

One might think something is wrong because both UR and ZC are higher than the schematic states. However with no current we would expect to find the voltages higher, what matters is the voltage under load conditions.

The LM340-T5 Regulator has a maximum current output of 1 amp so using ohms law we know the voltage is 5 volts and the current is 1 Amp, Resistance can be calculated using the formula R=V/I (R=5/1) so R=5Ω, Now that we know what to use, we can figure out the wattage, this is rather simple, Watts = Amps x Volts so in this case we have 5 volts, 1 Amp so need 5 Watts. For testing I use a couple of 5Ω 5W resistors , actually, I use 20 Watt resistors to keep from burning my fingers. Anything smaller than 5W will burn and smoke is bad. The load resistors are placed across pins 13 and 20 of the J1 connector

Bally Slot Machine Troubleshooting

To test the power supply drawing .5 amps we place 2, 5Ω resistors in series for a total of 10 Ω. With a 10 Ω load, drawing .5 amps these readings are fairly typical of what you should expect to see

UR = 12.16 VDC
ZC= 8.83 VDC
5v = 5.01 VDC

The final test is to test at full load, drawing 1 amp of current by removing one of the 5 ohm resistors so that only 5 ohms appears across pins 13 and 20 of J1, the readings you should expect to see would be.

UR = 7.57 VDC
ZC= 9.6 VDC
5v = 4.98 VDC

It would appear that the voltages shown on the schematic are voltages when the power
supply is measured with a full load.

I also recommend that when repairing these power supplies to remove the heat sinks from the bridge rectifier (BR1) and the 5 volt regulator (Q1). Clean off the old thermal heat sink compound and add new compound so that the heat transfer is more even. This will allow for maximum cooling.

The minimum voltage to expect from the LM340-T5 is 4.75 volts, if less than this then it is better to spend a couple of dollars and replace it.

Sometimes you will find that you have no voltage. In this case you want to check the 4 diodes and if the voltage seems to be half of what you expect then check the solder connections on the bottom side of the diodes. These will become bad because of heat. Other causes of no voltage is an open diode in the Bridge Rectifier (BR1).

I would recommend to anyone doing any type of repair work to invest in an ESR Meter. ESR means Equivalent Series Resistance and a high ESR can have adverse actions to your circuit. I have had several of these power supplies where despite changing the diodes, bridge rectifier and voltage regulator the output voltage was still below the regulators specified voltage of 4.75 volts @1 amp. These problems were resolved using my ESR meter and the discovery of the large 11,000 ufd capacitor having a high ESR value.

Bally S5500 Slot Machine Parts

Can’t run Tests

I have seen many complaints of not being able to run the tests or clear errors on these E Series machines. If you have a light tower the WHITE light should be illuminated before the tests or resets can be done. This does not mean that a burnt out bulb will prevent this but only serves as a quick indication that you should be able to run tests or clear error codes. If you find that you are unable to run the tests or reset the machine, check the cherry switch behind the door hinges. If this switch goes bad it will signal the MPU board that the door is closed. Many owners of these E machines will bypass the door switch however the cherry switch must be operational

RAM Tester

Since many of the problems with the E Series slot machine are related to RAM failures I thought it would be a good idea to have one hanging around in my shop. I searched the web and located a guy that had developed a tester for testing the 6264 RAM chips. I sent him an email asking if this might be easily converted to test the 5101 RAM chip used in the Bally E Series slot machines and a large number of Bally Pinball machines. As it turned out he did not have a problem in making this modification as an ‘Engineering Change’ for me. My tester only tests the 5101 RAM chips, but NeoLoch Sales has since altered the design so that it will now test 5101, 6116, 21C14 and 9114 RAM Chips. It also will run on a 5, 12 volt power supplies or from a 9 volt battery.